Buy retractable safety gate
Free Shipping for orders over £99.50 to most EU locations!

Baby Gate FAQ

1. How does Retract-A-Gate work?

After installing the Retract-A-Gate mounting brackets, simply attach the retractable safety gate to either side of the doorway by fully snapping the safety gate into both brackets. The Retract-A-Gate baby gate has a secure lock on it, so once you pull the mesh across and hook it in place; you then lock the retractable safety gate. The lock is a double acting (and very secure but simple) push and then turn mechanism. This keeps the retractable safety gate from being pulled out or pushed down.

When you want to retract the baby gate, simply unlock and then unhook the handle rod from the brackets. Retract-A-Gate uses an internal spring to automatically rewind the mesh, no manual winding is required. The mesh can only rewind when the lock has been moved to the open position; preventing any inadvertent retracting of the mesh. The action of the Retract-A-Gate baby gate as it retracts is smooth, steady, and quiet. Once it is fully retracted, the mesh and handle are neatly contained. Retract-A-Gate is the ONLY retractable safety gate which retracts easily, quietly, and automatically.

The opening and closing process is very simple, can be done with one hand, and only takes a few seconds to do. We went to great lengths to engineer and design the Retract-A-Gate baby gate for safety AND convenience and are confident that you will be satisfied. For full installation instructions, click here (in PDF format and opens in a new window).

2. Will my child be able to squeeze under the gate?

When installed properly, there will be some give to the mesh due to the fact that it needs to be flexible in order to retract. However, if installed incorrectly there may be too much flexibility.

Follow these guidelines to minimize any issues:

  1. Make sure to always lock the retractable safety gate by pushing and turning the lock. This will keep the mesh taut and help prevent your child from pushing the mesh out.
  2. Be sure the base of the baby gate is sitting on the floor and is not mounted up off the floor at all. When in use there should be no more than about 6.5mm gap between the bottom of the mesh and the floor.
  3. If you have the retractable safety gate mounted near a step, make sure the mesh is at least 15cm back from the edge of the step. Being close to an edge can create a gap that babies may be able to push through.
  4. When the mesh is extended and locked, both the top and bottom should be tight with no slack. If there is slack in the bottom, it probably means the bottom brackets are spaced too close to each other (compared to the upper brackets). Adjust the brackets so the distance between them across the opening is identical.
  5. To apply a slight amount of additional tension before locking the mesh in place, tighten the roll of fabric (no more than 1/8 of a turn), and then lock the gate.

3. Will my child be able to climb over the Retract-A-Gate baby gate?

With a mesh height of 86cm, Retract-A-Gate is one of the tallest retractable safety gates available. When locked, the mesh is held taut, so it is difficult to push down. The Retract-A-Gate baby gate doesn't have any large openings or places where little ones can step up onto, so climbing over the baby safety gate would be difficult.

4. Do you make a retractable baby gate wider than 183cm? Could you make a custom one?

At the present time we only offer two standard sized retractable safety gates which fit openings up to 132cm and 183cm. Some possible solutions for wider openings are below:

Option 1

The best option is to connect multiple Retract-A-Gates together using Connector Straps. How this works is the handle rod of one gate connects to the rod of the reel section on the next gate (pictures). This can be repeated with as many gates as you need to cover your opening. The benefit of this solution is that you can still easily use one hand to open or close the gates. If you decide to use this solution, make sure to always lock ALL gates connected together. This solution is only for special situations such as non-critical applications or where only a visual barrier is needed. Hooking multiple gates together with Connector Straps has not been certified for use with children. It is just a special option for non-critical applications. There are 43cm Connector Straps available for purchase on the "Online Store" page if you decide to use this option.

Retract-a-Gate user's guide for pet and child safety gates. Retract-a-Gate user's guide for pet and child safety gates.

This use of Retract-A-Gate is for special circumstances only.

Option 2

Some customers have hooked two Retract-A-Gates together using two S-hooks in order to cover up to 264cm/366cm. Each retractable safety gate mounts to either side of the opening, and then the handle rods hook together in the middle with the S-hooks. One S-hook would be used in the top cutouts and one S-hook would be used in the bottom cutouts (Pictures). This solution is also for special situations such as low traffic areas, non-critical applications, or where only a visual barrier is needed. Retract-A-Gate is very easy to operate with one hand; however, when using this option, you would need two hands and the process will be slower.

Retract-a-Gate user's guide for pet and child safety gates. Retract-a-Gate user's guide for pet and child safety gates.

This use of Retract-A-Gate is for special circumstances only.

The S-hook solution has not been tested or certified for use with children, it's just a special option for non-critical applications. If you decide to use this option, a set of S-hooks is available for purchase on the "Online Store" page for only £2.00.

Option 3

The only other option to allow the safety gate to span a wider distance would be to put up a partition to close the gap and then attach Retract-A-Gate to that. You could then paint or stain the structure to match the surroundings.

5. The Retract-A-Gate baby gate has been tested and passed The European Standard EN1930:2011; what does that mean?

The European Committee for Standardization (CEN) was officially created as an international non-profit association in 1975. CEN is a major provider of European standards and technical specifications. In being the leading provider of European standards, part of their mission is to satisfy consumer concerns by ensuring the quality, safety, and environmental requirements for juvenile products. Each of the 33 European member countries has adopted these standards.

The European Standard EN1930:2011 specifies the safety requirements and test methods for child safety barriers for indoor use to limit children’s access in the home. Retract-A-Gate has been professionally tested by an independent testing facility and has been approved to be in compliance with the European Standard EN1930:2011. Our customers can rest assured that Retract-A-Gate exceeds all quality and safety requirements to keep their little ones safer.

6. Why is the baby gate specified for ages 6 months through 24 months?

6-24 months is an age range which most baby gates are certified for by independent testing organizations. The common belief by testing organizations is that beyond 2 years children start to become strong enough and smart enough to open most baby gates. A small child wouldn't figure out the lock on the Retract-A-Gate baby gate unless they were shown how, since you have to push down and turn at the same time (kind of like child-proof caps). Retract-A-Gate is designed to be very easy for adults to operate, but would be difficult for small children to open the baby gate.

7. How is Retract-A-Gate better than other baby safety gates?

Smart Retract has done extensive testing of all the other retractable gates on the market. The main difference is simply quality. Retract-A-Gate is priced very competitively and offers the most value of any gate in its class. No other safety gate is as easy to use while keeping your little ones safer. Other retractable gates have complicated parts and don't hold up well to extended use. It is tempting to buy something cheaper, but the old adage of 'you get what you pay for' is very true here as well.

Here is a quick list of why Retract-A-Gate is better:

  • Other gates have a loud ratcheting noise when retracting; Retract-A-Gate is quiet.
  • Some gates make you manually rewind them; Retract-A-Gate rewinds automatically.
  • A few claim one-hand operation; Retract-A-Gate truly has simple, one-hand use.
  • Others use complex parts for installation; Retract-A-Gate is simple and fast to install.
  • Pausing while opening or closing other gates causes them to jam; Retract-A-Gate was engineered to avoid this cumbersome method of use and operates smoothly.
  • The mounting hardware for other gates is ugly and stands out; Retract-A-Gate mounting brackets are clear and virtually invisible.
  • Retract-A-Gate is the only retractable gate designed for both indoor and outdoor use.
  • The widest any other retractable gate can cover is 140cm; Retract-A-Gate can accommodate openings up to 183cm.
  • Any other gate is limited to its maximum opening; several Retract-A-Gates can connect together to cover as wide as you need (this is for special circumstances only).
  • No other gate on the market allows for simple relocation; the brackets for the Retract-A-Gate are universal and allow quick, easy relocation.
  • The Retract-A-Gate is one of the tallest available with a mesh height of 86cm.
  • There are many gates that specify using the gate for just children or just pets. Retract-A-Gate was engineered for use with both children AND pets.

Retract-A-Gate was designed with ease of installation, ease of use, durability, and safety in mind. It offers the best balance of features and security of any gate in its class.

 

Installation

1. What measurements do I need to know before I install my Retract-A-Gate?

We offer two Retract-A-Gate models which fit openings UP TO a maximum of 132cm or 183cm. These maximums are the total distance (gate and brackets) that the baby gate can cover. The height of the mesh on the retractable baby gate is 86cm and the total height to the top of the lock is just under 97cm.

The mounting brackets are 6cm wide, mount at about 8cm and 79cm off the floor, and require about 6cm of flat surface to attach to. There is some leeway to the height for where the brackets are mounted, especially on the reel side that holds the safety gate. When completely retracted, Retract-A-Gate is less than 10cm wide.

When the retractable baby gate is mounted in a doorway, most doors will still be able to close with the mounting hardware and baby safety gate in place. If you don't have the 6cm necessary to mount your baby gate in the doorway, the brackets can also mount around the corner of the doorway, either on the door molding or on the wall as long as you do not exceed the maximum distance it can cover.

If there are baseboards or skirting boards in the area where you will be installing your Retract-A-Gate, you might need wall spacers. For more information on wall spacers, go to our "Online Store" page. In the description of the Wall Spacer Set will be a link to help you determine if you need that item.

2. What accessories do I need for installing my baby gate?

For a normal doorway, hallway or walk-way installation (no stairs, baseboards or skirting boards interference), with the bracket screws drilled into a solid wall, no other accessories should be needed. For more information, please visit our "Online Store" page which lists all the retractable safety gates and accessory items that we offer. In the description of each item is a link to help you determine if you need that safety gate accessory.

3. Can Retract-A-Gate be installed at the top and bottom of the stairs? How many Banister Adapter Kits will I need?

Retract-A-Gate is certified for use at the top and bottom of the stairs, has been tested for that application, and can withstand a push out force of up to 100kg.

When attaching to the banister post

Mounting brackets can be screwed directly onto your stair banister, however if you do not want to drill into this you can use a Banister Adapter Kit. The brackets that come with each retractable baby gate screw into the Banister Adapter, then that assembly ties to your stair post using the straps provided with the kit. The Banister Adapter straps can accommodate up to 18cm square posts.

Our Banister Adapters are designed to also work with iron spindles. For thick iron spindles the adapter would fit against the metal, or if the spindle is small about 2.5cm, it fits into the gap between the two sides of the adapter.

When installing at the top of stairs

We recommend that you mount the retractable safety gate a minimum of 15cm back from the edge of the top step; being close to an edge can create a gap. If this is a problem for you, Retract-A-Gate is very unique in that it can be installed diagonally, at any angle, which can help achieve the 15cm requirement by angling it away from the stairs. Another option would be to block off near-by areas which still restrict access to the stairs.

When installing at the bottom of stairs

For the bottom of the stairs we recommend mounting the Retract-A-Gate on the floor and not up on a step. If the safety gate was mounted up on a step a child would have further to fall if they stepped up and then fell backwards.

How many do I need?

If you are going to attach both sides of your baby gate to stair posts, then you will need two Banister Adapter Kits. Only one Banister Adapter Kit would be required if you have a wall on one side of your staircase that you will be attaching to.

Which size do I need?

We offer two lengths of Banister Adapters: 91cm or 122cm. The 91cm adapter will work for most installations and the 122cm adapter is for taller posts. For example, some posts have flat or rounded areas at the top and bottom and then are narrow in the middle. The adapter is designed to span over this narrow area to provide a level surface for the brackets. If the distance from the floor to the upper round or flat area of the post that the adapter must reach is more than 91cm you will need the 122cm adapter. The adapter may be cut shorter (using any type of saw) to avoid standing taller than your stair post. The adapter cannot be cut any shorter than 81cm.

More detailed information

For full installation instructions; click here (opens in a new window).

4. Can the Retract-A-Gate baby gate be installed diagonally?

Absolutely! A nice advantage of Retract-A-Gate is that it can be installed on a diagonal and work at pretty much any angle, opening up numerous mounting options. This is just one of the many great retractable baby gate features which few if any other baby safety gates on the market have.

You can also diagonally attach Retract-A-Gate to a wall further away from the top of the stairs in order to help keep it back the recommended 15cm. For the best security with an angled installation the openings of the brackets should face away from the Retract-A-Gate.

5. What other surfaces can I install the gate to?

There are many alternative surfaces that the Retract-A-Gate can be mounted to. Some of the more common ones are listed below along with what you need to consider for that surface.

Bookcase or cabinet

You can mount the brackets to a bookcase only if the bookcase is stable (wall-mounted). You may need to put a backing board on the inside wall of the bookcase (or cabinet) if the wall is thin so that the screws have a minimum of 2.5cm of solid wood to bite into.

If you wish to mount the Retract-A-Gate baby gate to a cabinet where there is a small counter top overhang, the wall spacers can be used under both the top and bottom brackets. The spacers should move the safety gate out away from the counter's edge to provide enough clearance to mount the baby safety gate.

Brick, stone, concrete, or mortar

You will need appropriate masonry anchors which you can purchase at any hardware store. Simply take the screws that come with Retract-A-Gate to the store and have them size an appropriate masonry anchor for you. The screws we provide are 5cm long. If you need to use shorter screws be sure to use #6 (3.5mm) flat head screws and use the included finishing washers. Another option would be to fasten a board to the brick/stone/concrete/mortar using similar anchors and then attach the brackets to the board.

Fiberglass

We always recommend mounting the brackets to the support/stud behind the fiberglass as that will provide the best holding power. If there is no support then you need to use appropriate anchors that work with your fiberglass.

Cladding or Vinyl siding on a house

You can attach the retractable baby gate mounting brackets to the house cladding or siding as long as there is solid wood sheeting/boards underneath the cladding or siding (this is normally the case).

6. Can the gate be used outdoors?

Absolutely! Retract-A-Gate has been extensively tested in wet rainy seasons and hot dry summers. We have also tested the retractable safety gate outside during harsh winter conditions with flawless results. With that said, we do recommend you bring the Retract-A-Gate inside during freezing temperatures (simply unsnap the safety gate from the brackets). Anything, including Retract-A-Gate, which is left outside will have a reduced life compared to only indoor use; but you can feel confident that the retractable safety gate will stand up well to outdoor use. One thing to be aware of is that some fading or degradation due to extended sun exposure is possible. Because of this, we recommend bringing the Retract-A-Gate indoors when not in use.

Installing on Wooden Decking?

If installing outside to wooden decking, the deck posts will normally be a 15cm x 15cm wooden post. In this application we would recommend pre-drilling your holes and using stainless steel screws the same size as the ones we provide (#6 3.5mm flat head). Stainless steel will hold up much better when in contact with the wood posts that are used on the decking.

You can also attach the mounting brackets to your house siding if there is solid wood underneath.

 

MISCELLANEOUS

1. What is the mesh fabric of the baby gate made of and how durable is it? Can I get a sample of the mesh?

The mesh fabric used for Retract-A-Gate is a tough, non-toxic, reinforced polymer composite. Our material does not contain Lead, Phthalate, Latex or BPA chemicals and is formaldehyde free. We're proud to say that we are totally committed when it comes to eliminating those chemicals. The mesh is very durable, yet still allows you to clearly see through it. The retractable safety gate mesh material is UV and mildew resistant. In other applications this same mesh is used for truck tarps to hold down cargo.

Would you like a sample?

If you would like a sample of the mesh, be sure to include your name and mailing address and we will be happy to send you a small fabric sample of both the White and the Café Retract-A-Gate mesh. Just e-mail our customer service at: info@SmartRetract.co.uk

2. How do I clean the Retract-A-Gate baby gate?

Retract-A-Gate can be cleaned with mild soap and water as needed. For stubborn stains rubbing alcohol can be used.